Mallorca Villa Experts

Pools

Pool Valet in-floor cleaning system: common faults and repairs

How the Pool Valet in-floor cleaning system works, why nozzles stick or the water valve stops switching, what you can check and when to call a technician.

Pool technician at the edge of a villa pool inspecting a pop-up cleaning head from an in-floor cleaning system

Pool Valet is not a chlorinator or a robot cleaner. It is an in-floor cleaning system made by Paramount Pool & Spa Systems in the United States, and it is built into some villa pools in Mallorca. Pop-up nozzles set into the floor, steps and benches push dirt towards the main drain, one zone at a time. Because the system is driven by water pressure and has no electronics, there are no error codes: faults show up as symptoms. This guide covers the most common ones, based on Paramount's owner's manual. (A French distributor also sold a range of robot cleaners called Pool Valet around 2012; this guide is about the in-floor system.)

How the system works

Water from your normal pool pump goes to a water valve, also called a distribution valve, with between 2 and 12 ports. Inside, a module with gears and pistons sends the water to one circuit of nozzles at a time, much like a garden sprinkler system. The nozzles on that circuit pop up, spray across the floor and drop back when the valve moves on to the next circuit. Dirt is pushed towards the main drain and caught in a debris canister or the filter. The system needs good water pressure at the valve: Paramount specifies at least 20 psi, about 1.4 bar.

Nozzles stay up when the pump is off

The usual cause is sand or debris jamming the nozzles, often after the filter has been cleaned in a way that let dirt back into the pool. Use the run/pause switch on the water valve to isolate that circuit, then, with the pump running, push the nozzles down several times with your foot or a pool pole.

Nozzles on one circuit stay up all the time

If the nozzles of one circuit stay up after the valve has moved on, but drop when the system is off, a piston in the valve module is probably jammed open by debris. With the pump off, remove the module, rinse it by moving it back and forth in the pool, and push any open pistons closed without rotating them. Refit it and test. If the problem returns, the module needs replacing.

The water valve never switches circuits

If the same circuit runs all the time, check in this order:

  • The run/pause switch has not been left on pause
  • The gears in the module turn freely and are not jammed with debris
  • No nozzles have been swapped between positions or replaced with the wrong size
  • No circuit is completely blocked
  • The pressure at the valve is high enough: Paramount says above 25 psi, about 1.7 bar

A module whose gears no longer turn needs replacing.

The pool is not as clean as it used to be

This is usually a pressure problem:

  • Clean the filter when its pressure gauge reads about 5 psi (0.35 bar) above the clean reading
  • Empty the skimmer, pump and debris canister baskets
  • Check that the main drain is not blocked
  • Run the cleaning cycle for longer

If one area stays dirty even though its nozzle pops up, the nozzle is probably blocked. Remove it, run the pump briefly to flush the line, clear the debris and refit the nozzle in exactly the same hole.

Leaks at the water valve

Water seeping from the valve lid usually means the lid O-ring is stretched or damaged, or there is debris in its groove. Clean the groove, refit or replace the O-ring and tighten the band clamp gently and evenly. Paramount's manual says not to lubricate the O-ring and never to use petroleum-based products on it.

Things that damage the system

  • Using the run/pause switch again and again with the pump running can damage the diaphragms in the valve and module
  • Putting nozzles back in the wrong positions causes poor cleaning and, according to Paramount, can severely damage the equipment
  • Opening the water valve with the pump on is dangerous: switch off all equipment first, and never stand over the equipment when you restart the pump

Parts and repairs in Mallorca

Paramount parts are sold through pool distributors, and Spanish suppliers stock nozzle heads for Pool Valet and Paramount's related PV3 system. According to one distributor, the original Pool Valet nozzles have been discontinued and Pool Valet Retro nozzles are the replacement, so check compatibility before you order. A technician who knows in-floor systems can identify your valve and nozzle type, replace the module or O-rings and rebalance the circuits.

Top Clean, sold in Spain, is a similar pop-up system. The general principles are the same, good pressure, a clean filter and free-moving nozzles, but follow its own technical guide for the details.

Planning a project?

Describe it once. Vetted specialists in your area will be in touch with quotes, free and with no obligation.

Start your request